Your Plumbing Crash Course: Tips for Bathtub Installation

Call Today

What are your insights and beliefs about Installing A Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably tough task. If the old tub is easily easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub as well as position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools and material list should make up the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited gain access to that is commonly the case.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly originate from the pipes. Once the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. As soon as the taps have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
    Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin ensuring that the washers remain in location in between the faucet as well as the sink. Secure the faucet in place with the maker given backnut. Once the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type must be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Using both wooden boards under its feet, place the bathtub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small points.
    The next goal is to guarantee that the tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the tub till the level reviews degree.
    To mount taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the same for the other tap.
    Turn on the water supply and inspect all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Load the bath tub as well as also check the overflow electrical outlet and the typical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has actually been utilized a minimum of when as this will resolve it right into its final placement.

    Getting ready for the Installation


    To start with, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
    Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last position.

    Tiling Around the Tub


    In the area where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall between the bath and also the tiling, causing complications with wetness and possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your components and fittings. They are sold in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the market. It is recommended to fit the floor tiles making use of water-resistant or waterproof glue and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you appreciate reading about A Step-by-Step Guide to Installing a Bathtub? Write a remark down the page. We would be interested to hear your opinions about this write up. We are looking forward to see you back again soon. Kindly take the time to promote this post if you enjoyed it. I truly appreciate reading our article about How to Install a Bathtub Yourself.


    Tailored emergency solutions; call now.

    Leave a Reply

    Your email address will not be published. Required fields are marked *